跳至正文
OpenAgentSkill
浏览已开放 · 目录记录日期 2026-11-21 · 自动更新和账户服务暂时关闭。
安全

pfc-burger-viscoelastic

Select, probe, calibrate, and audit the Burger viscoelastic contact model for PFC 5.0 asphalt-mixture cases, including Maxwell-Kelvin parameter roles, units, temperature/rate dependence, PFC5 cmat assignment, timestep checks, creep/recovery validation, and PFC5-only syntax boundary checks.

Echo-aloha · 已有 AI 审核记录

安装与使用

运行命令前先阅读来源与依赖说明。复制命令不会自动安装或执行。

npx skills add Echo-aloha/asphalt-codex-skills-5 --skill pfc-burger-viscoelastic

技能说明


name: pfc-burger-viscoelastic description: Select, probe, calibrate, and audit the Burger viscoelastic contact model for PFC 5.0 asphalt-mixture cases, including Maxwell-Kelvin parameter roles, units, temperature/rate dependence, PFC5 cmat assignment, timestep checks, creep/recovery validation, and PFC5-only syntax boundary checks.

PFC Burger Viscoelastic Contact Model

Use this skill for the viscoelastic contact-law stage of pfc5-asphalt-workflow. Burger may represent homogenized asphalt mastic behavior at selected contacts, but it does not by itself create an explicit binder phase or guarantee mixture-scale behavior.

When to use

  • assign or audit Burger contacts in a PFC5 asphalt specimen;
  • interpret Maxwell and Kelvin spring/dashpot roles;
  • fit temperature- and rate-dependent mixture/mastic response;
  • build a two-contact or small-RVE verification probe;
  • review a Burger command block for non-PFC5 contamination.

Do not use this skill to invent production constants from a generic table.

Required inputs

  • PFC2D or PFC3D 5.0 and the unit system;
  • object/contact pairs that Burger is intended to represent;
  • all Burger properties with units, or raw calibration curves with units;
  • test temperature, loading rate/frequency and conditioning history;
  • specimen/contact geometry and resolution used during inverse fitting;
  • target creep/recovery, dynamic modulus/phase or other macro curves;
  • material level and test provenance: binder, mastic or mixture; for JTG 3410-2025 inputs, record the exact DSR/BBR/MSCR/LAS or mixture-performance method rather than writing only “rheology data”;
  • contact replacement policy for existing versus future contacts;
  • bur_mode tensile-mode choice and the required gap/opening behavior; for any parallel-bond/Burger mixture, also record fraction, selection rule, random seed and spatial-distribution audit;
  • any accelerated-time mapping, the preserved constitutive invariants and an unaccelerated pilot used to quantify its error;
  • timestep/damping/stop criteria and acceptance tolerances.

Constitutive interpretation

Burger combines a Maxwell branch (spring plus dashpot in series) and a Kelvin branch (spring plus dashpot in parallel). Normal and shear directions have separate parameters. Stiffness-like terms control instantaneous/delayed compliance; dashpot terms control time scale and permanent or delayed deformation. Friction and interface choices remain separate physical assumptions.

Property names and dimensions are syntax-family-specific. Read references/burger-theory.md for theory and references/pfc-command.md for version-labelled syntax notes.

Workflow

  1. Freeze units, temperature, rate/frequency, geometry and contact-pair meaning.
  2. Verify the PFC5.0 Burger property names with a minimal runtime probe.
  3. Run a minimal PFC5 two-body contact probe: contact creation, load/hold/unload, recovery, save/restore and property listing.
  4. Install the model using PFC5 cmat semantics, distinguishing future defaults from current-contact changes.
  5. Re-equilibrate the specimen and preserve a pre-load save.
  6. Freeze Burger bur_mode before calibration. PFC5 documents mode 0 as allowing tensile normal force and mode 1 as not allowing it, while the contact is active only for non-positive gap. If Burger is mixed with a damageable bonded model, freeze the populations and selection rule; record which model carries transient tension, separated-gap cohesion, friction and damage.
  7. Classify every curve as binder, mastic or mixture before fitting. JTG T 0627/T 0628, T 0647 and T 0648 binder data are priors or trend constraints, not direct mastic-contact targets. Only a declared test on the same mastic may target a mastic RVE; contact constants still require inverse fitting through the fixed PFC discretization.
  8. Treat beam/contact closed-form mappings as dimension-checked initializers, then inverse-fit the fixed PFC discretization; do not report the initializer as calibrated.
  9. Validate creep and recovery at the calibration condition, then confirm at another duration/rate/temperature or independent specimen.
  10. For time compression, derive the dashpot transform from the declared t -> t' convention, compare with an unaccelerated pilot, and keep the case labelled as a surrogate unless moving-load/path equivalence also passes.
  11. Check timestep sensitivity and rerun the target Marshall/rutting pilot.

Working rules

  • PFC5 is the only supported target in this package. Unsupported-major-version command blocks are rejected, not retained as migration references.
  • Do not use numerical “60 °C reference values” as production defaults; their units, geometry scaling and provenance are not established for the user's case.
  • Do not copy a published random Burger-contact fraction into another specimen. Contact topology is a calibrated stochastic variable, not only a material constant.
  • Do not describe Burger as categorically “tensionless.” In PFC5, bur_mode=0 can retain tensile normal force and bur_mode=1 suppresses it; however, Burger becomes inactive at positive gap and has no bond-strength/damage law. If another model supplies separated-gap cohesion or damage, expose and validate that division of responsibility under loading, unloading, opening and reversal.
  • Burger has no property inheritance, contact methods, or energy partitions in the PFC5 help. Assign all required properties explicitly and mark Burger-specific energy output unavailable rather than inventing a history.
  • Never reuse one parameter set at another temperature without an explicit, experimentally supported shift/fitting method.
  • Do not mix binder-level JTG 3410-2025 outputs with mixture-level T 0738/T 0745/T 0719 curves as if they had the same geometry or stress measure. Record the scale transition and validate it through the RVE/specimen.
  • Do not label a binder DSR/BBR curve as mast
阅读完整来源 ↗